section 10.8.3.3.3 & 10.8.3.3.4

Sriram Srinivasan srirams at lsil.com
Thu Oct 19 12:10:02 PDT 2000


* From the T10 Reflector (t10 at t10.org), posted by:
* Sriram Srinivasan <srirams at lsil.com>
*
Richard,

   I understand the intention behind your wordings, but u have replied 
to a message that was in the middle of the thread!  George sent out one 
on 16th Oct. on 10.8.3.3.4.
   
   {Sriram}
   
~ 
~ * From the T10 Reflector (t10 at t10.org), posted by:
~ * Richard Moore <richard.moore at qlogic.com>
~ *
~  >-----Original Message-----
~  >From: George_Penokie at tivoli.com [mailto:George_Penokie at tivoli.com]
~  >Sent: Friday, October 13, 2000 6:39 AM
~  >To: Sriram Srinivasan
~  >Cc: t10 at t10.org
~  >Subject: Re: section 10.8.3.3.3 & 10.8.3.3.4
~  >
~  >
~  >If the nexus has been fully identified (i.e., an I_T_L_Q nexus has 
been
~  >established) and the target detects an iuCRC error in any SPI 
command
~  >information unit it receives while in the DT DATA OUT phase the 
target
~  >shall, before receiving another SPI L_Q information unit,
~  >switch to a DT
~  >DATA IN phase and send a SPI L_Q/SPI status information unit
~  >pair to the
~  >initiator with a CHECK CONDITION status and a sense key set to 
ABORTED
~  >COMMAND and the additional sense code set to iuCRC ERROR
~  >DETECTED for the
~  >task associated with the iuCRC error.
~ 
~ It might have been the last command, so I think that should say
~ "before sending or receiving a SPI L_Q information unit for a 
different
~ I_T_L_Q nexus". Note the added words at the end, since it doesn't make
~ sense to require that a SPI L_Q/SPI status information unit pair be 
sent
~ "before sending another SPI L_Q information unit".
~ 
~  >If  the  nexus  has  been fully identified (i.e., an I_T_L_Q
~  >nexus has been
~  >established)  and  the  target  detects  an  iuCRC  error  in
~  >any SPI data
~  >information  unit  or SPI data stream information unit it
~  >receives while in
~  >the  DT  DATA  OUT  phase  the target shall, before sending
~  >another SPI L_Q
~  >information  unit,  switch  to  a  DT  DATA IN phase and send
~  >a SPI L_Q/SPI
~  >status information unit pair to the initiator with a CHECK
~  >CONDITION status
~  >and a sense key set to ABORTED COMMAND and the additional
~  >sense code set to
~  >iuCRC ERROR DETECTED for the task associated with the iuCRC error.
~ 
~ Again, you can't require that the SPI L_Q/SPI status IU pair be sent
~ "before sending another SPI L_Q information unit", so I suggest also
~ changing
~ this to "before sending a SPI L_Q information unit for a different 
I_T_L_Q
~ nexus".
~ 
~   -- Richard Moore
~      QLogic Corp. 
~ 
~ *
~ * For T10 Reflector information, send a message with
~ * 'info t10' (no quotes) in the message body to majordomo at t10.org
~ 



----------------------------------------------------------------------
	"FORGET NOT THAT THE EARTH DELIGHTS TO FEEL YOUR BARE FEET,
               AND THE WINDS LONG TO PLAY WITH YOUR HAIR"
                                          -Khalil Gibran

 Sriram Srinivasan                       Sriram.Srinivasan at lsil.com
 ASIC Design Engineer, LSI Logic,
 2001 Danfield Ct., 				Phone: 970-206-5847
 Fort Collins, CO 80525				FAX  : 970-206-5244
----------------------------------------------------------------------

*
* For T10 Reflector information, send a message with
* 'info t10' (no quotes) in the message body to majordomo at t10.org




More information about the T10 mailing list