To: t10@t10.org
Subject: Reminder, SAS PHY teleconference 6/14/07 10 am CDT
From: Alvin.Cox@seagate.com
Date: Wed, 13 Jun 2007 17:43:29 -0500
X-Message-Number: 7849
Formatted message: HTML-formatted message

Next call June 14.
Toll Free Dial in Number: (877)810-9442 
International Access/Caller Paid Dial In Number: (636)651-3190 
PARTICIPANT CODE: 3243413 
Webex information: 
https://seagate.webex.com/seagate 
Topic: SAS-2 PHY WG 
Date: Thursday 
Time: 10:00 am, Central Daylight Time (GMT -05:00, Chicago) 
Meeting number: 826 515 680 
Meeting password: 6gbpsSAS 
Agenda: 
1. StatEye simulations status:
Harvey, Kevin, Mike
SAS-2 Channel StatEye Simulation Results (07-253) [Witt] 
http://www.t10.org/ftp/t10/document.07/07-253r0.pdf 
2. SAS-2: Improving a Jitter Definition (07-205) 
http://www.t10.org/ftp/t10/document.07/07-205r0.pdf 
Feedback is needed from other measurement equipment suppliers regarding 
the comments below.
Comments from Bent Hessen-Schmidt, SyntheSys Research, Inc.: 
I suggest that we use text equivalent to: 
The Reference Clock characteristics are controlled by the resulting JTF 
(Jitter Transfer Function) characteristics obtained by taking the time 
difference between the PLL output (the Reference Clock) and the data 
stream sourced to the PLL. The PLL CLTF -3 dB corner frequency, and other 
adjustable CLTF parameters such a peaking, are determined by the value 
required to meet the requirements of the JTF. 
The JTF shall have the following characteristics for an encoded D24.3 
pattern (1100110011 0011001100). This is the MFTP which is a test pattern 
that has clock-like characteristics and a transition density of 0.5. 
1) The -3 dB corner frequency of the JTF shall be 3 MHz +/-1 MHz. 
2) The magnitude peaking of the JTF shall be 3.5 dB maximum. 
3) The attenuation at 30 KHz +/-1% shall be 75 dB +/-3 dB. 
The JTF -3dB corner frequency and the magnitude peaking requirements shall 
be measured with sinusoidal PJ applied, with a peak-to-peak amplitude of 
0.3 UI +/-10%. The relative attenuation at 30 KHz shall be measured with 
sinusoidal phase (time) modulation applied, with a peak-to-peak amplitude 
of 20.8 ns +/-10%. 
You will see that we have changed to from 72 db to 75 dB and from 2.1 MHz 
to 3 MHz and added the word “relative” to the last sentence. Relative 
should indicate that the 75 dB are with respect to the actual magnitude of 
jitter on the 30 kHz stimulus. The +/-10% therefore merely sets the 
starting point and still allows the other vendor. All uncertainties are 
then included in the +/-3 dB term. Effective tightening of the tolerances 
can be seen on the residual of the 30 kHz being confined to less than 5.2 
ps instead of (7.4 x 1.1 x 1.1 ps = 8.95 ps). 
3.  10-meter cable specification (06-499r2)
Time domain versus frequency domain concerns.
4.  Zero-length test load  (07-013)
Update?
5.  Additional items and updates. 
Alvin Cox
Seagate Technology, LLC
Office 405-381-8067
Cell 405-206-4809
E-Mail	alvin.cox@seagate.com